一早就來求助了(關于DC-Jack可靠度標准) 可靠性技术 新手提问 07年9月21日 编辑 skinner 取消关注 关注 私信 這么一個問題,我們的產品中一個D/C-Jack在客戶那邊出現中間PIN斷掉的現象,現在供應商也有給出原因/對策以及相應試驗,但我們客戶在問有沒有這個DC-Jack中間PIN承受力的國際標准.或其它相關的試驗(國際)來體現這個中間PIN的可靠度…. 感謝大家了……誰知道麻煩回一個貼子呀……..:handshake 给TA打赏 共{{data.count}}人 人已打赏
fulinkk lv3lv3 07年9月26日 我们这边一般是这样: 整机 1.插拔3000次,性能OK,无明显磨损 2.负荷测试水平,垂直方向5kg,性能ok,无断裂,脱焊 SMT方面会做pin脚推力测试,不过不是我们做,标准不太了解了,好像是2kg(不可靠,最好查查,这个有标准的)
fancy lv3lv3 07年9月24日 onenotebookDC-Jacklifetestconditionforyourreference 1.Total10Kcycles 2.mate/umatedmethod: Performablindinsert.(Donotlookatthenotebook-sideconnectorwhileinserting).Gripthecableapproximate10cmfromtheconnectorbaseandpullthecableatapproximatelya30-degreeanglefromthebase.This30-degreeangleshouldrotatefromleft,up,right,down(ifpossible)andrepeating. 3.failurecriteria:noanyBroken,bent,recessed,orliftedpins
angel8679 lv3lv3 07年9月21日 ANSI-EIA364-05B,我认为这个比较适合。关于connector的插拔力试验标准[url=http://www.kekaoxing.com/club/thread-1320-1-1.html]http://www.kekaoxing.com/club/thread-1320-1-1.html[/url] admin的资料链接一下:P [[i]本帖最后由cliffcrag于2007-9-2114:00编辑[/i]]
天下 lv2lv2 07年9月21日 [quote]原帖由[i]skinner[/i]于2007-9-2108:57发表[url=http://kekaoxing.com/club/redirect.php?goto=findpost&pid=9181&ptid=1535][img]http://kekaoxing.com/club/images/common/back.gif[/img][/url] 大家幫我看看這個是什么, EIA-364-13D(MatingandUnmatingForcesTestProcedureforElectricalConnectors/連接器的匹配和非匹配力的試驗程序) [/quote] 是一个连接器相关的标准: 1.1Scope Thisstandardestablishesamethodtodeterminetheforcesrequiredtomateandunmateelectricalconnectorsorprotectivecapswithconnectors,connectors/socketswithgagesordevices.Unlessotherwisespecifiedinthereferencingdocument,methodAshallbeused. 可惜平常没用过。
skinnerA lv0lv0 07年9月21日 大家幫我看看這個是什么, EIA-364-13D(MatingandUnmatingForcesTestProcedureforElectricalConnectors/連接器的匹配和非匹配力的試驗程序) [url]https://www.kekaoxing.com/d/uploads/standard/EIA/EIA-364-13D%20Final.pdf[/url]
天下 lv2lv2 07年9月21日 接插件方面的标准应该是有的,关于结构方面的可靠性,因为平常不太注意,好像看过些类似的标准,也给忘了,其他了解的朋友帮忙一下吧。。 [url]http://www.kekaoxing.com/design/otherdesign/200709/849.html[/url]机械可靠性的设计方法概述刚在前页看到这篇机械可靠性方面的文章,可以了解一下。
我们这边一般是这样:
整机
1.插拔3000次,性能OK,无明显磨损
2.负荷测试水平,垂直方向5kg,性能ok,无断裂,脱焊
SMT方面会做pin脚推力测试,不过不是我们做,标准不太了解了,好像是2kg(不可靠,最好查查,这个有标准的)
DCJACK廠商應對這個很專業,在做完成插拔疲勞後再測試一下插拔力就可以了!
onenotebookDC-Jacklifetestconditionforyourreference
1.Total10Kcycles
2.mate/umatedmethod:
Performablindinsert.(Donotlookatthenotebook-sideconnectorwhileinserting).Gripthecableapproximate10cmfromtheconnectorbaseandpullthecableatapproximatelya30-degreeanglefromthebase.This30-degreeangleshouldrotatefromleft,up,right,down(ifpossible)andrepeating.
3.failurecriteria:noanyBroken,bent,recessed,orliftedpins
當然問了﹐就是他們不知道才來這里的呀
ANSI-EIA364-05B,我认为这个比较适合。关于connector的插拔力试验标准[url=http://www.kekaoxing.com/club/thread-1320-1-1.html]http://www.kekaoxing.com/club/thread-1320-1-1.html[/url]
admin的资料链接一下:P
[[i]本帖最后由cliffcrag于2007-9-2114:00编辑[/i]]
不知道楼主有没有问DC-Jack器件的产家,直接问他们是根据什么标准进行检验或测试的,可能效率会更高些。
[quote]原帖由[i]skinner[/i]于2007-9-2108:57发表[url=http://kekaoxing.com/club/redirect.php?goto=findpost&pid=9181&ptid=1535][img]http://kekaoxing.com/club/images/common/back.gif[/img][/url]
大家幫我看看這個是什么,
EIA-364-13D(MatingandUnmatingForcesTestProcedureforElectricalConnectors/連接器的匹配和非匹配力的試驗程序)
[/quote]
是一个连接器相关的标准:
1.1Scope
Thisstandardestablishesamethodtodeterminetheforcesrequiredtomateandunmateelectricalconnectorsorprotectivecapswithconnectors,connectors/socketswithgagesordevices.Unlessotherwisespecifiedinthereferencingdocument,methodAshallbeused.
可惜平常没用过。
大家幫我看看這個是什么,
EIA-364-13D(MatingandUnmatingForcesTestProcedureforElectricalConnectors/連接器的匹配和非匹配力的試驗程序)
[url]https://www.kekaoxing.com/d/uploads/standard/EIA/EIA-364-13D%20Final.pdf[/url]
看看先,先謝了
我還在找這方面的標准呢
接插件方面的标准应该是有的,关于结构方面的可靠性,因为平常不太注意,好像看过些类似的标准,也给忘了,其他了解的朋友帮忙一下吧。。
[url]http://www.kekaoxing.com/design/otherdesign/200709/849.html[/url]机械可靠性的设计方法概述刚在前页看到这篇机械可靠性方面的文章,可以了解一下。